Flight controller SpeedyBee F405 V4 30x30mm

Name: Flight controller SpeedyBee F405 V4 30x30mm
Brand: SpeedyBee
SKU: 17968
Price: 1502 UAH
Availability: InStock
Rating: 4.5 (47 reviews)

Price:1 502 uahPrice in USD:35.00

Brand: SpeedyBeeSKU 17968

Description

SpeedyBee F405 V4 flight controller provides high accuracy and flexibility for a variety of FPV drones. It features a built-in barometer for precise altitude determination and a MicroSD card slot that allows you to record up to 4GB of Blackbox data. A special 6-pin connector is provided for connecting digital systems such as the DJI Air Unit, and is compatible with DJI O3, RunCam Link, and Caddx Vista. The controller supports dual BECs with 3A output current at 5V and 9V, which ensures stable power supply to peripherals. Six UART ports allow you to connect a receiver, GPS, camera, VTX and other devices. The ability to power the GPS via the USB port allows you to configure the system without a battery.

Features

Built-in barometer for accurate altitude calculation
SD card slot supports up to 4GB of Blackbox data
Dedicated DJI Air Unit connector for fast digital assembly
Dual 5V and 9V BECs now updated to 3A output current
4 x UART for your receiver + VTX + camera + GPS
Power your GPS with a USB cable - no battery required

Specifications

F405 V3 FC flight controller

MCU: STM32F405
IMU (Gyro): ICM42688P
USB Port: Type-C
Barometer: built-in
OSD Chip: AT7456E chip
BLE Bluetooth: supported (Used for flight controller configuration)
WIFI: not supported
How to connect DJI Air Unit: using a 6-pin connector or soldering
DJI Air Unit 6-pin plug: fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1
Blackbox MicroSD card slot: Compatible with standard (SDSC) or high capacity (SDHC) cards up to 32GB
Current Sensor Input: Supported (for SpeedyBee BLS 55A ESC, set scale = 400 and offset = 0)
Input power: 3S - 6S Lipo
- 5V Output - 9 groups of 5V output signal, four +5V pads and 1 BZ+ pad (used for Buzzer) on the front side and 4 LED pads
- 5V Total current load 3A
- 9V output - 2 groups of 9V output signals, one +9V terminal on the front side and the other is connected to the connector on the bottom side. Total current load 3A
- 3.3V output - designed for receivers with a 3.3V input. Current load up to 500 mA
- 4.5V output - used for the receiver and GPS module, even when the FC is powered via USB. Current load up to 1A
ESC outputs: M1 - M4 on the bottom side and M5-M8 on the top side
UART: 6 sets (UART1, UART2, UART3, UART4 (for Bluetooth connection), UART5 (for ESC telemetry), UART6)
ESC: Telemetry UART R5(UART5)
I2C: supported
Traditional Betaflight LED panels: supported
Buzzer: BZ+ and BZ-, which are used for Buzzer 5V
RSSI input: yes
Smart Port/F.Port: not supported
Firmware support: BetaFlight(Default), INAV
Firmware target: SPEEDYBEEF405V4
Mounting scheme: 30.5x30.5mm (4mm hole diameter)
Dimensions: 41.6*39.4*7.8mm
Weight: 10.5g

*Note: BOOT button. Usage options:
[A]. Simultaneously press and hold the BOOT button and turn on the FC to make the FC enter DFU mode. This is to flash the firmware when the FC is closed.
[Б]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom side. By default, short press the BOOT button to switch the LED display mode.
Hold down the BOOT button to toggle between SpeedyBee-LED and BF-LED modes. In BF-LED mode, all LED1-LED4 strips will be controlled by Betaflight firmware.