• Home
• Store
• Electronic FPV components
• Flight controllers

-0%

×

Matek H743-WING V3 flight controller for flying wing

Price:5 171 uah with VATPrice in USD:124.00

Bonuses will be issued for this product upon purchase

Read more

Brand: MatekSKU 15504

Out of stock

Notify when available

Description

The Matek H743-WING V3 flight controller utilizes the latest and highest performance H743 processor, which runs at 480MHz and 1Mb RAM. The board has a new CAN port to support future UAVCAN peripherals.

Matek H743-WING works with ArduPilot, BetaFlight and iNAV firmware(off. firmware page).

What's new in the H743-Wing V3?

• A new ICM42688-P(V3)+ICM42605 gyroscope is used instead of two MPU6000(V2)+ICM42605 gyroscopes
• Compatible with new firmware versions of ArduPilot plane 4.2.0+ and INAV 5.0+
• PDB/current sensor moved from FC board to bottom plate
• Moved 8A BEC from top board to bottom board
• Installed JST-GH connector for CAN port instead of JST-SH connector
• Added JST-GH connector for I2C2 for plug and play connection with ASPD-4525 air speed sensor.

Features

• Processor: STM32H743VIT6, 480MHz, 1Mb RAM, 2Mb memory
• Accelerometer / Gyroscope: ICM42688-P and ICM42605 (SPI4)
• Barometer: Infineon DPS310 (I2C2)
• OSD: AT7456E (SPI2)
• Blackbox: MicroSD card slot (SDIO)
• UART ports: 7 (1,2,3,4,6,7,8) with built-in inversion
• PWM outputs: 13 (including LED pad)
• I2C ports: 2
• CAN port: 1
• SPI3 breakout output: 1
• 3 x LEDs for FC STATUS (blue, red) and 3.3V BEC indicator (red)
• ADC (ADC): VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2
• Separate board: USB Type-C / beeper
• Switchable inputs for dual camera use
• Switchable BEC: 5V / 9V (12V)
• High accuracy current sensor: Yes
• ADC voltage divider VB2: 1K: 10K
• ADC AirSpeed ADC voltage divider: 10K: 10K
• INAV TR / SA VTX control: yes
• Squeaker support: yes
• RSSI: yes
• Analog Speed Sensor Connection: Yes
• Digital speed sensor connection: Yes
• Static Power: 160mA at 5V
• INAV Firmware: MATEKH743
• Firmware: ArduPilot (ChiBiOS): MATEKH743
• BetaFlight Firmware: MATEKH743
• Mount: 30.5 x 30.5mm, hole diameter 4mm, with 3mm spacers
• Dimensions: 54 x 36 x 13mm
• Weight: 30g (with USB extension cable)

PDB

• Input Voltage Range: 9 ~ 36V (3 ~ 8S LiPo) with TVS protection
• Outputs for ESC: 2
• Current sensor: 132A, 3.3V ADC (scale 250 in INAV, 40A/V in ArduPilot)
• Battery voltage sensor: 1:10 (scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
• Current sensing resistor: 60A continuous, 132A pulse
• BEC 5V output
  • Designed for flight controller, receiver, OSD, FPV camera, buzzer, LED module, GPS module, AirSpeed sensor
  • Continuous current: 2A (max. 3A)
• BEC output 9V / 12V
  • Designed for video transmitter, FPV camera, LED module
  • Continuous current: 2A (max. 3A)
  • 12V option with jumper
• BEC Vx output
  • Designed for servos
  • Adjustable voltage: 5V by default, 6V or 7.2V with jumper.
  • Continuous current: 8A, (max. 10A)
• BEC output 3.3V
  • Designed for Baro / Compass and Spektrum RX module
  • Linear regulator
  • Continuous current: 200mA

Recommendations

• The H743-WING has pre-installed Betaflight firmware for quality control purposes
• The ArduPilot firmware supports the built-in DPS310 barometer starting with the stable version Plane-4.0.6 and Copter-4.0.4.
• Problem Solution: H7 AutoPilot is not initialized with Ardupilot firmware
• If you download the ArduPilot firmware to the controller via the INAV / BetaFlight configurator. A known issue is that the download process hangs at 50% if "full chip erase" is selected. It is highly recommended to use STM32CubeProgrammer to erase the MCU and load the firmware. Official manual from Matek
• Crossfire support only exists in the "latest" version 4.1, not in version 4.0.x, if you are downloading the "latest" version 4.1, set SERIAL7_PROTOCOL = 23, RSSI_TYPE = 3.

Accessories

• 1 x Matek H743-WING flight controller
• 1 x USB adapter (Type-C) / squeaker (active)
• 1 x JST SH-4P to GH-4P cable for CAN port, 20cm
• 1 x SH-6P to SH-6P cable for USB adapter, 20cm
• 1 x dupont 2.54 pin set (connectors not soldered to the board)

Files

• Руководство пользователя Matek H743-WING V2 на английском языке

Useful links

• Официальная страница с прошивками для Matek H743-WING

Photos