• Home
• Store
• Electronic FPV components
• Flight controllers

-0%

×

Matek F405-SE AIO flight controller

Price:2 257 uah with VATPrice in USD:53.99

Bonuses will be issued for this product upon purchase

Read more

Brand: MatekSKU 14689

Out of stock

Notify when available

Description

Matek is replacing the F405-CTR controller with a new version of the F405-SE. The new controller uses a modern DPS310 barometer, the maximum input voltage has increased to 36V (8S LiPo), and the number of PWM outputs has increased from 6 to 9, UART from 5 to 6, and I2C from 1 to 2.

Note: the memory card shown in the photo is not included.

Controller characteristics

• Processor: 168MHz STM32F405RET6
• Gyroscope: MPU6000 (SPI)
• Barometer: DPS310 (I2C)
• OSD: BetaFlight OSD on AT7456E (SPI)
• Blackbox: MicroSD slot (SPI)
• Firmware:
  • INAV target: MATEKF405SE
  • BetaFlight target: MATEKF405SE
  • ArduPilot target: MATEKF405-WING
• Interface: VCP, 6 x Uarts, 1 x Softserial_Tx
• PWM outputs: 9 (7 BF/INAV compatible Dshot outputs)
• I2C: 2
• ADC: 3 (voltage, current, RSSI)
• RX6: 4 (one per corner) for BLheli_32 ESC telemetry
• ESC power/signal: 4
• Contacts for 4in1 ESC Signal/GND: G/S1/S2/S3/S4
• LEDs: 3
  • Operating Status: Blue, Red
  • 3.3V indicator: red
• Integrated Inventor for SBUS (UART2-RX)
• PPM/UART common: UART2-RX
• Vbat filter output for VTX power supply
• Camera control: supported
• Smartaudio and Tramp VTX protocol: supported
• DJI FPV OSD Protocol: Supported
• WS2812 LED strip: Supported
• Beeper: supported
• RSSI: supported
• Mounting holes: 30.5 x 30.5mm, Φ4mm with Φ3mm spacers
• Size: 36 x 46mm
• Weight: 10g

Characteristics of built-in PDB

• Input power supply: 6~36V (2~8S LiPo) with surge protection
• Configuration: 4 sets of 35A outputs (max. 4 x 46A)
• BEC: 5V 2A (max. 3A)
• 3.3V LDO controller: max. 200mA
• Current sensor: 184A (scale 179 in INAV / BF)
• Battery voltage sensor: 1K: 10K

Accessories

• 1 x Matek F405-SE flight controller
• 6 x M4 to M3 silicone spacers
• 1 x FR4 PCB plate 36 x 36 x 1mm
• 1 x Rubycon ZLH 35V / 470uF capacitor (low ESR)

Recommendations

• *** known issue / bug: BetaFlight does not support the DPS310 barometer running with the STM32F405
• F405-SE has pre-installed INAV firmware for quality control purposes
• INAV2.5.1 downloaded from the configurator does not support the new DPS310 barometer. download custom firmware from here
• The DPS310 barometer will be officially supported by INAV2.6 and the new configurator
• ArduPilot firmware "MATEKF405-WING" until June 25 does not support the built-in DPS310 barometer. Please download the latest firmware version from the official website here
• inav_2.5.1_MATEKF405SE_DPS310.hex
• If the barometer cannot be detected, enter the command in INAV CLI mode:
  • set baro_hardware = DPS310
  • save
• betaflight_4.2.0_MATEKF405SE.hex
• Known issue / bug: DPS310 will not work even if you enter the following CLI command
  
  • set baro_bustype = I2C
  • set baro_i2c_device = 1
  • set baro_i2c_address = 118
  • set baro_hardware = DPS310
  • save

Files

• Руководство пользователя Matek F405-SE AIO

Useful links

• Официальная страница Matek F405-SE AIO (настройка, рекомендации, прошивки)

Photos