• Home
• Store
• Devices
• Action cameras and accessories

-0%

×

BEC board to build a Naked GoPro HERO6/7

Price:379 uah with VATPrice in USD:8.99

Bonuses will be issued for this product upon purchase

Read more

Brand: BetaFPVSKU 16070

Out of stock

Notify when available

Description

BEC board from BetaFPV to build a GoPro Naked HERO6 or HERO7. The board has a built-in 5V 2A BEC and weighs only about 1.5 grams, making your Naked GoPro very neat and lightweight.

Features

• Specially designed for Naked GoPro HERO6 or HERO7
• Very light weight, only 1.5g
• BEC output voltage is 5V at 2A
• Built-in standard GoPro buttons: power/mode select button and record button
• Built-in GoPro LED indicator to determine the status of the camera
• Pilot can control GoPro recording via radio transmitter
• GH 1.25 3P connector for quick connection to flight controller for power and recording

Features

• Input Voltage: 2-4S LiPo
• BEC: 5V @ 2A
• Connector: GH 1.25 3P
• Weight: 1.53g

Instructions and tips

BEC board schematic

The two buttons on the BEC board have the same functions as the GoPro buttons:

• Power on - press the power/mode button, the LED will blink three times and turn off
• To start recording video, press the Record button once and the LED will start flashing slowly. If the LED blinks once and goes out, it means there is no SD card available
• Stop recording - press "Record" button, the LED will stop blinking slowly

LED indication

To start using the camera, first connect the GH1.25 connector to the BEC and then apply power to the quadcopter. The LED on the board will blink once, then you must press the power/mode button on the BEC board once to turn on the GoPro Naked HERO6/7 camera. The LED on the BEC board has the same state as the standard LED on the GoPro motherboard.

How to set up remote recording

In order to use the toggle switch on the radio hardware to start or stop recording video, you need to do some additional customization.

For example, if you are using a BetaFPV F4 FC V2.0 controller in your drone (such as in the BetaFPV 95X series drones), the wiring diagram is shown below. The yellow cable (FC B12 pin pad) is for starting remote recording only.

BetaFPV uses the Pinio function in Betaflight to control the recording. First configure the Pinio function for pin B12 on the FC board.

resource FLASH_CS 1 NONE
resource PINIO 1 B12
set pinio_box = 40,255,255,255,255
save

Next, map one of your radio transmitter's toggle switch channels to the Pinio function (aka USER1). As shown below, map the AUX4 channel in the radio transmitter to the Pinio's USER1. The cursor in the orange area means the button is released, and the white area means the button is pressed. So keep the cursor in the orange zone by default.

Third, check to see if the Pinio function is working. Change the switch and move the cursor from the orange zone to the white zone and finally back to the orange zone. Now you can check the LED status to see if recording is starting. Use the same process to stop recording.

If you are using a 12A F4 AIO FC controller, such as on the BetaFPV 85X series drones, you will use the LED_STRIP pin (pin A08) for the Pinio function.

resource LED_STRIP 1 NONE
resource PINIO 1 A08
set pinio_box = 40,255,255,255,255
save

Learn more about the Betaflight Pinio function here.

Note: The Flymod store is not responsible for any tampering or rebuilding of the GoPro Hero. Reassembling your GoPro will void your warranty, and you may end up breaking your camera if something goes wrong. The various disassembly guides are not authorized by GoPro, and your camera is not guaranteed to work afterwards.

Accessories

• 1 x BEC board for GoPro HERO6/7
• 1 x GH1.25 power cable (90mm 30AWG)

Photos