TheSpedix IS30 for 2-4S LiPo sets a new standard for 4-in-1 speed controllers. Many ESCs used in FPV racing quadcopters have 3.3 × 3.3 mm MOSFETs. Transistors of this size are generally less efficient and reliable. With the same dimensions, the carefully designed IS series of high performance regulators utilize 6 large 5 × 6 mm MOSFETs to meet the increasing current demand from power systems used in FPV racing. These MOSFETs are manufactured using the latest technology to promote better heat dissipation and reduce resistance. All this improves reliability compared to ESCs with smaller MOSFETs.
In addition, other factors such as improved design, fast EFM8BB21 microcontroller, independent half bridge chip and 3 Oz copper plated PCBs with high TG make the IS30 4-in-1 one of the best in the market.
Features
Standard mounting holes with 30.5mm spacing
Board dimensions are 36x41mm, the same as standard flight controllers.
Equipped with 6 standard MOS-FET DFN5X6 (5x6mm) transistors with better heat dissipation, lower resistance and higher reliability.
Runs on high performance EFM8BB21 MCU microcontrollers
BLHeli_S firmware is a more improved code based on the regular BLHeli. BLHeli_S are flashed and customized as easily and quickly as regular BLHeli.
Utilizes a more robust 7-pin Molex connector with 1.25mm pitch, containing 4 ESC signals, 5V power and VBAT
Additionally, three sets of pads are available. One 5V / 1.2A BEC and two at battery voltage level that can be used for video transmitters, accessories or an additional capacitor
Gap diameter around the mounting holes is 6mm
Characteristics
Current: 30A
Peak current: 40A
Power Support: 2-4S Lipo
IC: EFM8BB21 MCU
Firmware: BLHeli-S - DShot
Power Wires: 16 AWG
Size: 36mm x 41mm x 5mm
Mounting holes: 30.5mm x 30.5mm
Weight (without wires): 10.3г
Accessories
1 x IS30 4-in-1 ESC
1 x 16 AWG power wire
7-pin bare wire connector
7-pin connector with servos (1x3pin with BEC, the rest are single connectors)
1 x 25V 330μF Rubycon ZLH electrolytic capacitor, used for additional peak voltage suppression, must be soldered to the battery connection pins.
Можно ли запитать от его 5V передатчик TBS и полётный контроллер RaceFlight Revolt?
В интструкции к регулятору указано 5,2V 1,2A по факту 5,4V
Не накроется ли передатчик и полётный контроллер от 5,4V ?
Если TBS на 800 мВт то может и не вытянуть все вместе на максимальной мощности. По поводу напряжения нужно еще проверить пртбор которым меряете, они часто врут, а вообще контролер и гироскоп питаются от линейного стабилизатора на 3,3 В питание напрямую уходит только на приемник, в передатчике тоже все питается через отдельные линейные стабилизаторы, сгореть не должно но будет чут больше нагрев. Еще этому регулятору обязательно нужно устанавливать хороший электролитические конденсатор на вход питания, емкость побольше, провода максимально короткие.
Brand: SpedixSKU 11492
Reviews and discussions
В интструкции к регулятору указано 5,2V 1,2A по факту 5,4V
Не накроется ли передатчик и полётный контроллер от 5,4V ?
Registration