TheiFlight ProTek25 Pusher Analog is a new evolutionary step in the ProTek series of bluewoop drones. This version features a new reverse frame structure with the motors facing downward, which increases the overall level of thrust and efficiency. The Pusher also features a significant weight reduction, down to almost 40 grams, and a smaller footprint.
When fitted with a 4S 650mAh LiPo battery and a Naked GoPro Hero8 action camera, the total weight will be less than 250 grams, allowing this FPV drone to be used without license and registration in most countries around the world!
The ProTek25 Pusher series of quadcopters is only manufactured in a 4S LiPo battery version.
Don't worry about customizing your quadcopter, iFlight has already done it for you! Basic PID and filter tuning has been applied for smooth freestyle flight.
Note:
PNP version means a receiver for radio equipment is NOT included in the kit
Batteries, GoPro and GoPro case pictured are NOT included in the kit
iFlight is constantly making changes to the ProTek25 Pusher's design and components, so different sources may give very different information. Our information is up to date for the current shipment. Information may change in the future!
VTX is set to 25mW by default.
Features
High quality T700 carbon fiber (40% more tensile strength than regular 3K carbon fiber)
Reverse frame design for increased traction and efficiency
Durable aerodynamic polypropylene body and two-piece carbon frame.
Powerful Xing 1404 motors/ Traction is more than enough for freestyle flying with Naked GoPro action camera It is lightweight, efficient and has maximum power for its size; Traction is more than enough for cruising and acrobatic flight without restrictions!
SucceX-D Whoop AIO V3.2 high-performance flight controller to save space and weight
Quality iFlight RaceCam R1 1200TVL 2.1mm micro size 19 x 19mm analog FPV camera
Easy assembly and disassembly, only 8 bolts need to be removed to detach the main plastic housing from the carbon fiber frame, motors and electronics
Drone is pre-configured and tested from the factory
Features
General
Flight Controller: SucceX-D Whoop AIO V3.2
Motors: Xing 1404 4600KV (4S LiPo)
FPV Camera: RaceCam R1 1200TVL 2.1mm 19 x 19mm
Frame size along motor axes: 108mm
Top plate thickness: 3mm
Distance between top and bottom plates: 21mm (height of aluminum struts)
Battery connector: XT30
Recommended propeller size: 2.5 inches
Recommended battery: 650-850mAh 4S LiPo
FC mounting pattern: 25.5 x 25.5mm / 20 x 20mm
FPV camera mounting distance: 20mm
Case Size: 76.3 x 76.3mm
Weight: 127g (without battery)
Flight Controller iFlight SucceX-D Whoop AIO V3.2
Processor: STM32F411
Gyroscope: MPU6000
Blackbox: 16Mb
BEC Output: 5V 2.5A
Interface: Micro USB
OSD: AT7456E
FC firmware: BetaFlight 4.2.9
Firmware target：IFLIGHT_F411_AIO
ESC rated current: 20A
ESC peak current: 30A
Input voltage: 2-6S LiPo
Current sensor: Yes
ESC firmware: BLHeli_S (G-H-30 BLS)
Mounting Diagram: 25.5 x 25.5mm / Φ3mm
Dimensions: 41 x 41mm
iFlight SucceX Mini Force video transmitter
Frequency: 5.8G
Power: PIT/25/200/400/600mW
Number of channels: 40
Antenna Interface: MMCX
VTX Protocol: IRC Tramp
Size: 29 x 29mm
Mounting pattern: 20 x 20mm, M3 / 25 x 25mm, M2
Weight: 4g
Accessories PNP version
1 x iFlight ProTek25 Pusher Analog FPV ready drone
2 x iFlight Nazgul 2525 propellers
1 x Velcro 15x150mm
1 x Velcro 15x180mm
1 x USB cable
Recommendations
First time using a ready-to-fly drone? iFlight has prepared a thorough article on a general guide to BNF/PNP drones to make getting into the FPV hobby as easy as possible!
Angle Mode (self-balancing mode) is enabled by default so that the first flight does not end in an instant crash. Please read this article "How to disable Angle Mode, activate acro mode"
Brand: iFlightSKU 16536
Reviews and discussions
There are no messages yet. Leave your message first.
Registration