• Home
• Store
• Ready to fly (RTF)
• Multicopters

-0%

×

Racing FPV quadcopter iFlight Nazgul5 HD 240mm PNP

Price:13 761 uah with VATPrice in USD:329.99

Bonuses will be issued for this product upon purchase

Read more

Brand: iFlightSKU 15587

• 6S LiPo. Nebula Pro

Select the option!

Out of stock

Notify when available

Description

TheiFlight Nazgul5 HD is a ready-to-fly 5-inch quadcopter with a Caddx Nebula Pro Vista Kit HD FPV digital system. The digital video signal allows for maximum image quality that cannot be achieved using conventional analog systems.

Features

• State-of-the-art Caddx Nebula Pro Vista Kit digital system (certified by DJI)
• iFlight XL5 V5 carbon fiber frame with 5mm thick beams and increased width toward the center of the mount for greater strength
• Popular True-X frame form factor
• Quick-change beam design
• LED illumination of the iFlight logo
• Assembly is based on the iFlight SucceX-E F4 V2.1 flight stack
• More power and smooth flight is guaranteed using the popular iFlight Xing-E motors with long-lasting NSK bearings
• Protective TPU plastic parts
• Mounting platform for GoPro type action cameras
• The drone is fully customized and tested from the manufacturer. Basic filters and PIDs are set up, and a few more additional software tweaks to improve flight quality

Note:

• Angle-Mode (self-balancing mode) is enabled by default so that the first flight doesn't end in a crash. How do I switch Angle Mode to Acro Mode?
• PNP version means that there is no receiver for radio equipment included (if you don't want to use DJI remote control, you can choose a receiver for your transmitter)
• The action camera and camera mount shown in the photo are not included in the kit (only the platform without the GoPro mount housing is included).

Features

Specifications of iFlight XL5 V5 frame

• Frame size in motor axes: 240mm
• Form factor: True-X
• Beam thickness: 5mm
• Top plate: 2mm
• Bottom plate: 3mm
• Side plates: 1.5mm
• Mounting Diagram: 30.5 x 30.5, 20 x 20mm
• Distance for FPV camera mounting: 19mm
• Size: 170 x 170mm

Specifications FPV camera Caddx Nebula Pro Vista Kit

• Matrix: 1/3 inch, CMOS
• Resolution: 720P / 120fps
• Aspect Ratio: 4:3/16:9 (switchable)
• FPV/video recording viewing angle:
  • Diagonal: 150°
  • Horizontal: 122°
  • Vertical: 93°
• Lens: 2.1mm
• Min. FPV latency:
  
  • 720p 120fps low latency: 12-28ms
  • High quality mode: 720p 60fps: 30-40ms
• Operating frequency: 5.725-5.850G
• Output Power: 25mW / 200mW / 500mW / 700mW
• Transmitter Power (EIRP):
  • FCC/SRRC/MIC: <30dBm
  • CE: <14dBm
• Max. transmission distance:
  • FCC/SRRC: 4 km
  • CE: 0.7 km
• Interface: USB-C, IPEX, 3-in-1 port
• Supported flight control system: F3, F4, F7
• Supported video goggles: DJI FPV googles
• Input voltage: 7.4-26.4V
• Vista board size: 30 x 29 x 13mm
• Nebula Pro FPV camera size: 19 x 19 x 20mm
• Weight: 27g / antenna: 2.5g

Specifications of iFlight SucceX-E F4

• Processor ： STM32F405
• Gyroscope： MPU6000
• Betaflight OSD： AT7456E
• BlackBox： 8mb
• Input voltage： 2-6S LiPo (max 8S 50V)
• PWM Outputs: 4
• UART outputs: 4 （1, 2, 3, 6)
• ESC outputs: 8
• VTX protocol: is （IRC Tramp）
• WS2812 LED strip: supported
• Squeaker： supported
• BEC: 5V / 2.5A
• Firmware： betaflight_4.0.5_BETAFLIGHTF4.hex
• Target： IFRC/IFF4_TWIN_G(STM32F405)
• Mounting holes: 30.5 x 30.5mm, φ4mm, with φ3mm dampers
• Dimensions: 36 x 36mm
• Weight: 7.6g

ESC 4-in-1 iFlight SucceX-E 45A Features

• Constant current: 45A
• Peak current: 55A
• Voltage support: 2-6S LiPo
• Processor: STM32F051, 48Mhz
• Current Sensor: Yes
• WEIGHT: no
• Firmware: BLHeli_S
• Protocols: DShot 150/300/600, MultiShot, OneShot
• Target: G-H-30 BLS 16.7
• Mounting holes: 30.5 x 30.5mm, φ4mm, with dampers φ3mm
• Dimensions: 40 x 43mm
• Weight: 14.4g

Features of iFlight Xing-E 2207

• RPM per volt: 1800KV
• Configuration: 12N14P
• Stator Diameter: 22mm
• Stator length: 7mm
• Magnets: N52SH
• Bearing size: 9 x 4 x 4mm
• Shaft diameter: 4mm
• Shaft Material: Steel
• Voltage: 3-6S LiPo
• No-load current at 12.6V: 1.2A
• Maximum peak current: 35.2A
• Maximum power: 845.3W
• Internal resistance: 81.5 ohms
• Mounting scheme: M3 thread, 16 x16 mm
• Motor size: 28.5 x 19.7 mm
• Weight: 33.1g (15cm wire)

Accessories

• 1 x iFlight Nazgul5 HD ready-made quadcopter
• 2 x iFlight Nazgul 5140 propeller kit
• 1 x wire set
• 2 x anti-slip mats
• 2 x iFlight Velcro
• 1 x Albatross LHCP RP-SMA 5.8G antenna
• 1 x protective tubes for receiver antennas
• 1 x Micro USB cable
• 1 x action camera mount
• 1 x manuals and instructions

Photos